Author Archives: Camille F.

Roofing Screws – A Metal Roofing Installation Essential

Posted on by

Three-inch self-tapping roofing screws are most frequently used to secure metal roofing, with the exception of the one-inch roofing screws which can sometimes be sufficient to attach the first edges of metal roofing sections. If, however, a metal roof is being installed on top of an existing asphalt roof, the first edges of each of its sections will have to be secured with three-inch roofing screws.

 

Self-tapping roofing screws are essential for simplifying metal roofing installation which has neither been factory pre-drilled nor dimple, because they are both faster to secure and reduce the risk of injury from snapped screws.

 

Sealing Metal Roofing

 

Because metal roofing has nothing in it which will seal the holes around roofing screws in the way asphalt roofing materials seal the holes around roofing nails, roofing screws manufacturers make two types of roofing screws. The first will have a sealer cap of metal which is seated directly on the roofing material and secured by the screw itself. The second will have washers of plastic or rubber integrated into their bodies, which automatically seal the holes in the roofing as they are inserted.

 

Roofing Screw Gun Alternatives

 

Metal roofing should not be hand-installed, because it demands that roofing screws be separated by no more than two feet. Driving this number of roofing screws by hand would quickly exhaust the hand and arm strength of the roofing crew, and relying on the rechargeable roofing screw guns now available would mean to switch to fresh batteries at hourly intervals. Because most rechargeable roofing screw gun batteries require a charging time of one hour, each roofing crew member would need four batteries to complete an eight hour shift!

 

One solution would be to use an electrically powered roofing screw gun which can operate without interruption for an entire day. Most of these screw guns are manufactured with adjustable power levels, enabling their users to select just the right amount of force to use when installing the roofing screws.

 

Roofing screws which are driven too deeply into a roof can either damage the roof itself or have their heaps snapped off, making them very difficult to remove. The disadvantage of using an electrically powered roofing screw gun is that it rewires the use of a long extension cord, which can be a hazard for those working on the rooftop.

 

The third alternative for installing roofing screws is the pneumatic screw gun, which is powered by an air compressor. The pneumatic patio roofing screw gun is attached to its air compressor by a long air hose, which like the extension cord on an electrical screw gun can be a real encumbrance when it is dragged around on the roof.

 

If you need further details about roofing screw and other screw series, welcome to visit our website and feel free to contact Fu Yeh – the various screw series manufacturing expert.

 

Article Source: http://EzineArticles.com/1442142

 

Understanding the Differences between Automotive and Industrial Greases

Posted on by

“Our plant is searching for a new type of grease. Can you explain the differences between industrial and automotive greases in composition, features, and performance requirements or in any other aspect?”

 

In short, there is really no difference between automotive and industrial greases. Grease selection will depend on the desired application and performance.

 

In regards to grease and its application, there are critical elements used in the formulation process that must be considered. These elements include the thickener type and concentration, lubricant type, viscosity and additive package. Greases are rated by the National Lubricating Grease Institute (NLGI) and range from 000 through 6. An NLGI 2 grade is typically the specification used in automotive greases.

 

One of the only differences between industrial and automotive greases is that a two-letter designation is often used in the automotive industry to specify the type of grease to employ. For example, greases may be rated as GC or LB. GC is recommended for axle and wheel bearing grease, while LB is the industry standard for chassis grease used on tie-rod ends, ball joints, U-joints and control-arm shafts.

 

Regardless of the application, greases should reduce friction and wear, protect against corrosion, seal bearings from water and contaminants, and resist leakage. While one of the main reasons for grease failure is selecting the wrong type of grease for the intended application, there may also be other causes, such as incompatibility resulting in excessive softening of the grease, contamination leading to excessive wear or applying too little or too much grease for the application.

 

For instance, in off-road equipment, the environment generally is harsh with a variety of factors to take into account including water, dirt, poor seals and heavy loads. In this type of situation, grease selection is key. You will need a grease with good rust protection, film strength and water resistance.

 

Bearings normally see less contamination but often experience wide variations of speed and temperature. In this case, you should choose grease with excellent oxidation stability, exceptional mechanical stability and good performance over a wide temperature range.

 

In summary, the constituents of industrial and automotive greases may be quite similar and should be treated as such. The point is that no matter the application in which grease is used, it is critical to know how to properly select a grease while keeping in mind all of the important parameters.

 

If you need more information about MoS2 grease and lubricants, welcome to visit the website of Min Jung Hong – the quality and professional high performance motor oil manufacturer.

 

Article Source: http://www.machinerylubrication.com/Read/29910/automotive-industrial-greases

 

What is a Hydraulic Power Pack Unit?

Posted on by

Hydraulic Power Pack Units are the main driving components of hydraulic systems. Consisting mainly of a motor, a reservoir and a hydraulic pump, these units can generate a tremendous amount of power to drive most any kind of hydraulic ram. Hydraulic power pack units are based on Pascal’s law of physics, drawing their power from ratios of area and pressure.

 

Hydraulic power pack units are used in a wide range of applications, including:

 

  • Machine Tools
  • Automation
  • Meat Processing Machinery
  • Mobile Equipment
  • Aerospace Test Equipment
  • Rolling Mill Machinery
  • Material Handling
  • Agricultural Equipment
  • Paper Mill Machinery
  • Government/Military
  • Oil Field
  • Oil Spill Clean Up Equipment
  • Industrial Process
  • Marine Equipment
  • Construction Equipment
  • Theatrical & Production Equipment

 

Hydraulic power pack units can generally be used in any application that requires heavy and systematic lifting or other requirements for the repeated use of powerful and directional force.

 

Consider all of the ways that hydraulic power pack units are used in things you see every day. Drive past any construction site and you’re likely to see some kind of heavy construction machine, be it a bull dozer, an excavator or even a skid steer. All of these machines rely on hydraulic power units to do their work. Fishermen rely on hydraulic power units to lift their nets and pots. Your auto mechanic uses a hydraulic power pack unit to lift your car high enough to walk around beneath it and make repairs. The Jaws of Life, a tool that has saved many lives in auto accidents, relies on a hydraulic power unit for its incredible cutting power. Farmers use hydraulic-driven machinery to tend and harvest their crops. The garbage truck that picks up your trash uses a hydraulic power unit to compact the garbage it collects. Your favorite amusement park ride probably utilizes hydraulics to lift you high and fast into the air and give you a soft, safe landing. Remember when you stepped on the brakes to avoid that last small animal that ran out into the road? Modern auto braking systems rely on the power of hydraulics.

 

It’s easy to overlook the widespread and impressive utility of hydraulic power pack units, but listing all of their applications it becomes clear that we rely on them for so much of what makes our society run smoothly and efficiently.

 

If you need further details about hydraulic power pack unit and hydraulics manufacturer, welcome to visit the website of ANSON – the outstanding and professional hydraulic pump supplier in Taiwan.

 

Article Source: http://www.dhict.com/amc/faq-what-is-a-power-unit.php

 

Overview of Power Capacitors

Posted on by

What are they?

 

Power capacitors work by acting as a reserve power bank; they store the charge rather than being the source of power such as the battery. When you are listening to your music, and playing a heavy sub-bass note, the power will draw from the capacitor rather than from the battery so to ensure that the rest of the car will not be starved of power i.e. the headlights dimming. It will act as a buffer so that that the power being delivered to the amplifiers will not drop below the recommended voltages and be steady therefore reducing the risk of damage to the components.

 

So what power capacitor to choose?

 

After doing a bit of research, the general rule seems to be 1 farad per 1000 watts of power that your system is running at. So using that, a 1.5 farad power capacitor should be ideally suited to a 1500 watt system. There is a large selection of power capacitors available out there, for example, this power capacitor is a 2 farad power capacitor designed for smaller systems, this is not to say however that it will have a reduction in performance, however for those systems that require more power, a power capacitor with a higher farad will be able to deliver for longer and will usually be of a higher build quality.

 

How to install the capacitor

 

Ideally the capacitor needs to be installed as close to the amplifiers as possible. The capacitor requires a 12 volt positive from the battery and a separate ground, to the amplifier; so that the 12 volt positive is ‘inline’ with the terminal from the battery and the amplifier. The amplifier 12 volt positive is then taken from the capacitor while the amplifier is usually grounded separately as it is important to use as short a ground cable as possible to reduce any potential ground interference.

 

When you need to consider other alternatives

 

Power capacitors will not always be of help when you are listening to music, if the lights for example dim down, and stay dim, this indicates there is a deficiency of power and there are other methods of solving the problem, it could potentially be that the battery is not able to generate a charge sufficient enough to meet the demands, so installing a higher cranking battery is usually the common solution however it is possible that upgrading “The Big Three” may also solve the issue(see below for more details). It is also important to check that the current alternator can produce a charge that will be sufficient with a larger battery.

 

‘The Big Three’

 

The big three is a popular upgrade. It consists of upgrading three wires in the car to ones that are much thicker. As a result of using much thicker wire, more current is allowed to flow through; hence the overall effect seen will be that the voltage running through the car will be higher. The three wires that are upgraded are the wire from the alternator to the battery, the engine ground to the chassis and the battery ground to the chassis. It is common, but not always, that people will choose 0 gauge power wire when going about the big three upgrade. This is vital again to ensure that the voltage delivered to the amplifiers does not drop so low that the risk of damage is possible.

 

Conclusion

 

So in conclusion, there is no hard or fast answer to if a capacitor is necessary or not. However capacitors may have benefits if used appropriately. There are large selections of capacitors; some come with digital volt meters, distribution blocks etc., while others are purely chosen for aesthetic pleasure, I myself went for a 4 farad power capacitor with a built in digital volt meter with an LCD display so that it was something I was able to display and looks pretty damn cool.

 

If you need more details about power capacitors and capacitor supplier, welcome to visit our website and feel free to send inquiries to YUHCHANG – the outstanding and professional power capacitor manufacturer in Taiwan.

 

 

Article Source: http://EzineArticles.com/expert/Neil_Patel/563675

Article Source: http://EzineArticles.com/3791870

 

Excellent NF Series 5 Faces Machines Manufacturer – Vision Wide

Posted on by

Established in 1999, Vision Wide Tech Co., Ltd. is a professional 5 faces machines manufacturer which has global brand “VTEC”. We provide vertical machining centers and wide range of bridge type machining centers (vertical / five-side, fixed column / moving beam, box way / linear way).

 

Vision Wide provides various quality 5 faces machine series for customers. Today, we are going to introduce features of NF series 5 faces machining below:

 

NF Series Moving Beam/ Fixed Beam 5-Face Machining
NF series 5 faces machines

  • NF series high speed 5-face machines, with typical VW products features of rigid structure and high precision, are designed with 5-face function of multi-angle cutting and X-Y roller ways structure. It speeds up 3 axes rapid traverse and increases the machine’s efficiency of utilization.

 

  • Solid beam with big cross section and roller ways design strengthens the stiffness of Y-travel.

 

  • Wide base with 3 roller sliding ways improve the load capacity and dynamic accuracy.

 

  • Box structure of headstock with 6 guiding roller blocks, and 1- 1.4 meter Z-travel keeps stiffness and minimizes the interference between spindle and work piece, carrying the complete function of 5-face cutting. High efficient power transmission is made by well-arranged spindle motor position and short shaft device.

 

  • Automatic horizontal and vertical tool changer.

 

  • Automatic head magazine (one head).

 

  • AH attachment-Automatic 5-face function with 700mm longer Y-travel.

 

Would you want to get further details about NF series 5 faces machines? Welcome to visit website of Vision Wide, you can get information about detailed specifications, standard accessory & function. If you have any questions also welcome to send inquiry or contact us!

 

Vision Wide Tech Co., Ltd.

No.43, 17th Industrial Rd., Taiping, Taichung 41154, Taiwan

Tel: 886-4-2271 2000

Fax: 886-4-2271 2009

E-mail: info@visionwide.com.tw

 

 

Carbon Fiber Fabric: Unmatched Durability and Strength

Posted on by

Carbon fiber fabric is often considered to be one of the most significant inventions of the 20th century. Any manufactured item that requires being extremely strong and lightweight at the same time, probably makes use of it. In fact, it is so strong that it easily exceeds the maximum strength of even the strongest metals like titanium and steel.

 

What is Carbon Fiber Fabric?

 

It is derived from thousands of strands of carbon fiber. For manufacturing, millions of carbon atoms are bonded together in crystals that are more or less aligned parallel to the long axis of the fiber as the crystal alignment gives the fiber high strength-to-volume ratio ultimately making it extremely strong. The bundles of these fibers are then combined together to form a tow, which in further woven into a fabric. This is then given specific shapes by molding them with the use of epoxy resin along with other framing materials like aluminum and polymers.

 

Types of Carbon Fiber Fabric

 

Different types of products require different levels of fiber strength and depending upon these requirements, the right kind of it is used. There are primarily three categories: High Modulus (Aerospace Grade), Intermediate Modulus and Standard Modulus (Commercial Grade). The most commonly produced between the three is the commercial grade fiber, which is considered to be sufficiently strong for use in most everyday objects.

 

Uses and applications of Carbon Fiber Fabric

 

Because of its lightweight and extreme strength, it has been used in thousands of products that require being extraordinarily durable. From the exteriors of rockets and satellites to a simple product like a laptop case, it is used commonly in the manufacture of countless number of products. In fact, a lot of modern manufacturers have already made use of it on products that were manufactured by the use of metals like steel and titanium in the past. From sports items like tennis racquets to automobile exteriors and bicycle frames, the use of carbon fiber fabric is now more widespread than ever before.

 

Future of the Carbon Fiber Fabric

 

The consumption of carbon fiber fabric is only expected to grow in the near future. With the cost of production already declining, the use of it is expected to be more widespread in the near future. With customers already demanding more durable and safer products, the demand for it is extremely high. Thus, it will probably be an important part of the future of humanity.

 

In fact, Carbon Fiber Fabric is very strong and it can easily exceed the maximum strength of even the strongest metals like titanium and steel etc. used in the past.

 

Taiwan Electric Insulator specializes in carbon fiber fabric which is widely applied in sports, precision watch manufacturing, robotics, aerospace, flat panels, modelling, motor sports, aircraft, ship, automotive engineering, and more. The type of carbon fiber fabric is divided into 1K, 3K, 6K, 12K, 24K and glitter. It is committed to provide superior quality carbon fiber fabric to meet the complete needs of the customers. If you need further details about Carbon Fiber Fabric, welcome to visit our website and feel free to contact Taiwan Electric Insulator.

 

 

Article Source: http://EzineArticles.com/9351204

 

The Benefits of Using CNC Knee Milling Machine for Machining Tasks

Posted on by

Manufacturers, engineers, machinists, and the like are sure to realize huge benefits from using a revolutionary machining tool called CNC knee milling machine. Perfect for all types of users, from beginners to experienced ones, this tool can guarantee smooth and easy usage and, at the same time, increase the efficiency and productivity of workers. Unlike other types of milling machines, the x-y table of the knee milling machine rides up and down the column of a vertical knee that is adjustable.

 

One of the biggest advantages of using this type of equipment is the fact that machinists get to produce accurate machined surfaces, with excellent bolt patterns and edges, over and over again. The CNC technology or computer numerical code makes it all possible. Users simply have to input and save their tool path programs, which they can use as many times as they want. This innovative technology helps machinists save time and effort on the same process of creating the same products.

 

CNC knee milling machines also make users more efficient and productive, two important characteristics that are beneficial not just to the machinists themselves but to their customers as well. Certainly, customers would go back to providers who give them top-quality products in a timely manner.

 

Many machining companies as well as hobbyists have since started to use a CNC knee milling machine in order to accomplish their tasks more efficiently. This machining tool is also becoming a more popular alternative to the more rigid bed mill, and is now available in hundreds of local stores and online.

 

JIUH-YEH is a professional manufacturer specializes in manufacturing knee type milling machine and various types of milling machine and machining centers. If you need furthermore details about knee milling machine series or other milling machines, welcome to visit our website and feel free to contact Jiuh Yeh for more information!

 

 

Article Source: http://EzineArticles.com/5430361

 

Uses of Soap Dispenser Pump and What it is?

Posted on by

To start with what is a soap dispenser pump? The answer is it is a machine mostly used in bathrooms to spray liquid soap on the dirty hands of people to wash them and make them clean and hygienic. These pumps generally have two components; one is a pump and the other is a storage area where the liquid soap is stored.

 

These dispenser pumps are generally present in nearly every public bathroom nowadays and as well in most of the homes. Now the question arises why? The answer is, simply because we all live in an age where good sanitary measures seem to be growing increasingly important day by day due to the growing outbreaks of different types of viruses.

 

These different types of germs, dirt, and other bacteria’s can cause harm to our bodies, and any preventive measures that people can take will go a long way toward curbing the potential damage.

 

As it is a well-known fact that Liquid and foam soaps are more effective at cleaning than bar soaps and the idea of using soap that hasn’t been used by any other person is far more sanitary in people’s mind. The soaps with pleasant smell provide a soothing satisfaction on the users mind.

 

It is also possible that a person could be looking for a kitchen soap dispenser which can make the job of washing dishes easier, and can also help the ladies of the house to smile for a right reason.

 

A chrome dispenser pump gives off a luminous shine that has the sleek and ultra-modern feel that may complement the room where as a stainless steel soap pump will do the same thing, and looks great in kitchens with modern sinks and a ceramic soap dispenser will perfectly complement the rustic look.

 

Regardless of what a person is looking for, one can find it with a little effort, as a soap dispenser is far nicer than the ordinary plastic container that a bottle of soap may come in.

 

This is also very cost effective also as soap refills cost considerably less than soap straight out of the bottle and when bought in bulk, these refills can save a considerable chunk of change over the long haul. This gives a person yet another reason to buy a soap dispenser pump.

 

So it is recommended to visit websites which offer all types of required assistance to find the best available soap dispenser pumps in the market.

 

Aeco-Pack Corp. is a professional manufacturer and exporter of lotion pump, dispenser pumps, PET preform, PET bottles/containers/jars, trigger sprayers, and so on. If you need further details about dispenser pumps and other Aecopack’s containers, welcome to contact us!

 

Living Fountain Plastic Industrial Co., Ltd.

No.31, Ln. 198, Minsheng Rd., Wufeng Dist., Taichung City 413 Taiwan

Tel: +886-4-2331-8822

Fax: +886-4-2331-9922

E-mail: sales@living1991.com.tw

 

Article Source: http://EzineArticles.com/3671303

 

Overview of NC Rotary Indexing Tables

Posted on by

NC rotary indexing tables are used to index parts and components in defined, angular increments so that they can be machined, worked, or assembled in multiple operations. Tables consist of a circular steel plate, one or more spindles, a drive system, and pins that hold parts and components in place. Rotary indexing tables have either fixed or adjustable indexing angles. During each revolution, the table stops for a specified period of time so that an operation can be performed at each station. The bearings that support rotary indexing tables determine both the load capacity and accuracy. Angular contact bearings are more expensive than recirculating ball bearings, but provide better load capacity and axial stiffness. Cross-roller bearings are also commonly available.

 

NC rotary indexing tables are powered by pneumatic and electric motors, hydraulic drives, and manual actuation. Drive mechanisms can be located above, below, behind, or to the side of the table surface. Pneumatic rotary indexing tables are suitable for small and medium loads. They are powered by one of more pneumatic cylinders, each of which represents an index. During the return stroke, a pawl locks the table in place. With some devices, the pawl can be adjusted to change the number of indexes. Electrically-powered tables are generally faster than pneumatic devices and can handle heavier loads. Tables that are powered by hydraulic drives use a pressurized fluid that transfers rotational kinetic energy. Manually-actuated rotary indexing tables often include a hand crank or are loosened, turned, and adjusted by hand.

 

Selecting NC Rotary Indexing Tables

 

Selecting NC rotary indexing table requires an analysis of specifications and features. Specifications include maximum indexing increment, work table diameter, maximum axial load, and maximum radial load. A variety of features are available. Some table surfaces can be raised or lowered at a controlled angle. Others have more than one rotating work surface. Computer numerically controlled (CNC) devices provide greater accuracy and repeatability. Position encoders are often used to relay the position of the table surface. Both four axis tables and five axis tables provide variable X, Y, and Z axis motion. Four-axis table also provide part rotation along the X axis. Five-axis tables provide part rotation along both the X axis and the Y axis.

 

Applications

 

Applications for NC rotary indexing tables include assembly and equipment positioning, as well as various automation, inspection and machining applications. Most devices work well with machines that perform fast and simple vertical operations. Examples include industrial presses, screwdrivers, riveters, dispensers, pick-and-place units, and ultrasonic or resistance welders. Parts can be loaded and unloaded manually or automatically.

 

Established in 1996, Topsdisk is a professional NC rotary table manufacturer in Taiwan. We specialize in manufacturing NC rotary table, NC rotary tilting table, NC rotary indexing table, hydraulic / pneumatic index table, center tailstock, faceplate tailstock and so on. If you need more details about NC rotary indexing tables or other machine tools, welcome to visit our website and feel free to contact Topsdisk!

 

TOPSDISK Co., Ltd.

1F, No. 220, Shenlin S. Rd. Daya Dist, Taichung City, Taiwan, R.O.C

TEL：04-25682975

FAX：04-25681016

E-mail: cnc588588-5@yahoo.com

 

 

Article Source: http://www.globalspec.com/learnmore/manufacturing_process_equipment/machine_tool_accessories/rotary_indexing_tables

 

Choosing the Best Framing Nailer – Pneumatic Air Nail Guns

Posted on by

A pneumatic framing nailer gun can do a great range of jobs, from stud work to joists. You can nail down sub-flooring and even build trusses. You can fasten sheathing, nail decking, construct fences, and more. With a framing nail gun you can do all the rough wood work and more on just about any residential building. It’s a very important part of constructing a wood structure.

 

There are many different framing nailers on the market, from popular brands like Hitachi, Senco, Max, Bostitch, Paslode, Porter Cable, and Dewalt. How are you going to choose the best one for your needs? Since you’re not intending to buy all the pneumatic framing nailers out there, you need to educate yourself on what each nail gun has to offer.

 

I put this short guide together to help you do just that: choose the right nailer for your needs.

 

Some questions before you buy:

 

Weight – Are you concerned about the weight of the nail gun? Some builders look for the lightest framing nailer because they can work longer with less arm fatigue. That’s the benefit of a light-weight nailer.

 

Size – Size is also an important factor to some contractors and DIYers. A more compact sized framing nail gun can fit into tighter spaces to shoot the nails in the right spot. Some framing nailers can fit between studs and joists as narrow as 12 inches. Others are more bulky and you’ll have a hard time with tight areas.

 

Power – Pneumatic frame nailers range quite a bit in the power to drive nails. Some nail guns can shoot nails up to 3-1/4 inches long. Others can easily drive the larger 3-1/2 inch nails. Many framers don’t need to shoot nails any larger than 3-1/4 inches long. Others, on the other hand, prefer to have the extra power to drive larger nails when the need arises.

 

Features – What feature do you need in a nail gun? The modern guns have a vast array of features available. Some have selective triggers, where you can switch between contact nailing and sequential actuation nailing with the push of a button. Tool-free nail depth adjustment is also available on some framing nailers. A few are approved for use with specialty nails. It all depends on what you need (or want).

 

Our brand of Apach Frame Nailer is the right tool for nailing large pieces of material together quickly and accurately. Frame Nailer is ideal used for roofing, carpentry, joiner, framing, door, window, building components and other applications. Apach Frame Nailers can eliminate the need to hammer, save your hours of project time and save your muscles some undue soreness. Welcome to contact us for more information about our products.

 

APACH INDUSTRIAL CO., LTD.

176 Industrial 9th Rd, Tali Dist., Taichung City, Taiwan 41280

TEL: +886 -4-24915576

FAX: +886- 4-24915580

E-mail: info@apach.com.tw

 

 

Article Source: http://EzineArticles.com/5537837