Locking Caster Wheels: Wheel Only or Swivel & Wheel?

There are two types of locking caster wheels available. The normal “Wheel Brake” will only stop the wheel from rolling when you depress the brake pedal. Our “Total Locking” Brake will lock both the wheel from rolling and the swivel from turning at the same time. Which brake you choose depends on what you are going to do?

 

You Need to Determine The Use of Your Caster Object.

 

If this is a decorative table (like a coffee table or a side table) and no one will be sitting at it, chances are you don’t need to have a brake on the casters. If this is a table for eating, working or the like, you should install at least two caster wheels with brakes.

 

So to further analyze the use:

 

If it is mandatory that the work surface not move when bumped, even with a repetitive motion like carving meat or sawing wood, a total locking brake is required.

 

A swivel caster will have the tendency to pick up a repetitive motion and the swivel will allow the object to start to “rock” along with that motion. If you lock the swivel along with the wheel using total locking casters, you stop that motion.

 

Much More Locking Casters

 

If you need more choice of locking caster wheels, come and visit Enjoying Go Co., Ltd. – they are the professional caster wheel manufacturer in Taiwan. You can find chair caster, design caster, braking caster, PU logo caster, industrial wheels, and much more products there. Now, check out Enjoying Go’s website and feel free to contact them.

 

 

Article Source: http://www.needcasters.com/locking-casters-ALP.htm

Who Should Get A LCD Monitor Arm?

If you work at a computer for long periods of time, an ergonomic setup can help protect your health and well-being. To learn about ideal workstation setups, we referred to the work of ergonomics expert Alan Hedge, director of the Human Factors and Ergonomics teaching and research programs at Cornell University.

 

In Ergonomic Workplace Design for Health, Wellness, and Productivity, Hedge recommends that the top of a screen be about 2 to 3 inches above eye level, because human eyes see more below the horizon line than above. To find the right height, Hedge advises, ”the worker should sit back in their chair in a slight recline, at an angle of around 100°-110°, then they should hold their right arm out horizontally at shoulder level, and their middle finger should almost touch the center of the screen.” Getting your monitor position just right will let you see most of the screen without having to crane your neck. Hedge also recommends placing your keyboard just below your elbow level to ensure good posture and maintaining an elbow angle of 90 degrees or greater to prevent nerve compression.

 

On a laptop, this arrangement isn’t possible, because its screen and keyboard are so close together. If you use a stand-alone monitor to raise your gaze, you’re already helping your posture, but you may need a monitor arm to get the positioning just right.

 

A monitor arm can help prevent back and neck pain by properly positioning your screen. Especially if you alternate between sitting and standing at your desk, share a workstation with people of varying height, or just need easy, on-the-fly adjustments, you should consider a monitor arm like the ones we recommend here.

 

Monitor arms aren’t necessary for every person or every desk setup. If you don’t need to adjust your monitor’s height frequently, you can achieve ideal screen placement with a monitor stand, which is much cheaper and easier to set up, or even with a sturdy book or two. Our monitor picks come with adjustable stands that work for most people in most setups. But those included stands take up more space on your desk, lack the height to serve very tall people, lack the range for a proper sit/stand setup, and don’t move left and right, move forward and back, or rotate. If you need those features, you should get a monitor arm.

 

Modernsolid, founded in 1989, is the manufacturer of LCD monitor arm. Since 1996, Modernsolid sensed that LCD monitor is a growing trend and it would be suitable for various applications in fields ranging from business, office, industry, schools to healthcare market. Since then, Modernsolid has started to design and manufacture all kinds of mounting solutions to accommodate most LCD displays for improving ergonomics. With the insistence on high quality, Modernsolid has grown to be a world-leading supplier in mounting solutions including LCD Monitor Arm, TV Wall Mount Bracket and Hospital Arm, etc. Learn more information, please try to check out its product catalog and feel free to send inquiries to Modernsolid.

 

 

Article Source: https://thewirecutter.com/reviews/best-monitor-arms/

A Complete Buying Guide To Caster Wheel Replacement

One of the first things you will notice is that there are a surprising number of variations to choose from when you start shopping for caster wheel replacement. From dozens of different materials to the range of different diameters to all the added features and options you can choose from, it gets overwhelming.

 

To help you sift through the thousands of options, we’ve put together a quick guide specifically for buying chair caster wheel replacements. First, you’ll get a short guide to understanding what kind of factors you will need to consider while shopping.

 

Tips For Choosing The Right Caster Replacement Wheels

Getting the right caster wheel replacements comes down to 5 core factors: material, mount style, load capacity, wheel diameter, and extra options. Let’s take a look at each of those in more detail:

 

  1. Type of Material: there are dozens of different materials that a caster wheel can be made of. For most chairs, however, you are really only going to find either rubber or metal. There are, of course, exceptions. But, in general, your safest best is to look for replacement plastic caster wheels.

 

  1. Type of Mount: there are 3 main mount styles—plate, weld, and stem. If getting a stem caster wheels replacement, you’ll need to make sure the stem is the same as your current ones (i.e. – threaded, expandable, or grip ring). For plate mounts, the dimensions of the plates should match and the pattern for the bolt holes should be the same.

 

  1. Load Capacity: fortunately, this is a less important factor if you’re getting wheels for chairs. Since the total load the wheels will have to carry is almost certainly going to be less than 500 pounds, just about any wheel will do. Load capacity is affected by the material and the diameter of the wheel.

 

  1. Wheel Diameter: wheel diameters can range from 3 inches to 10 inches. The larger the diameter, the more easily it will roll. However, too large wheels may not fit on your chair legs or, if they do, it may look really weird.

 

  1. Additional Options: you don’t need too many additional options on your caster wheels for chairs. It’s generally nice to have a swivel style wheel so that you can move easily in any direction. If you don’t want your chair to move around, you may choose to get wheels with a locking mechanism. Or if you want to avoid crushing toes, you can get wheels with foot guards.

 

In the case of office chairs, the easiest way to make sure you choose correctly for each of these 5 factors is to simply remove one of the existing caster wheels and bring it with you when you go shopping. In many cases, there is a model or product number somewhere on the wheel.

 

If you can find that, you can shop online suing this number. In this case, you can try to buy the exact same wheels that you currently have. If they are no longer in production, you can at least find information on the specifications (i.e.- material, mount style, capacity, diameter, etc.) and then note those down so you can find new wheels that meet the same specifications.

 

Get more information about caster wheel replacement, I recommend you to visit the website of ENJOYING GO Co., Ltd. – this company is the well-known caster wheel manufacturer in the industry. They can provide you a variety of caster wheels including compression casters, furniture casters, braking casters, locking casters, custom casters, and so on PU casters. Please do not hesitate to check out ENJOY site for more enjoy chair caster wheels.

 

 

Article Source: http://casterwheelguide.com/replacement-caster-wheels/

Best Ergonomic Computer Desk Chair: Why Do You Need A Right Office Chair?

Relieve your tired neck and back with smart picks.

 

Why Do You Need A Great Ergonomic Office Task Chair?

 

If there is any one factor that you can change to make spending eight hours a day in an office easier, it’s your chair. There is no shortage of evidence proving that being stuck in a chair for too long can increase the risk of cardiovascular disease and worsen back pain. In fact, sitting too much is even called worse than smoking. Many people who have office jobs develop problems like numbness, spinal misalignment, joint pain, neck pain, and herniated discs — usually from sitting too long on a poor quality chair without support. While you probably do not want to spend a lot of money on a chair, a high quality ergonomic chair is an investment in your health, comfort and productivity.

 

Two separate studies, published in 1990 and 2003, found productivity goes up more than 17% when individuals work in an ergonomic setting with an adjustable chair. The right chair combined with ergonomic training can also reduce workplace injuries. Even if you do not already have wrist or back problems, an ergonomic chair can help you maintain the right posture to avoid strain, carpel tunnel syndrome, lower back pain, and spinal disc injury.

 

The National Institute of Health recommends choosing a chair with all of the necessary adjustments to support proper posture. This includes a chair with casters and a five-point base; a seat pan with dense, small-cell foam padding or coils; a backrest that is either curved or small enough to fit the small of the back; soft armrests with an adjustable height and width; a hydraulic seat heat adjustment feature; and a tilt adjustment to transfer some body weight to the chair’s backrest.

 

Wonderful Fuh Shyan Ergonomic Office Chairs

 

If you work on computer then you definitely need to invest a good ergonomic chair. I think Fuh Shyan’s ergonomic task chairs will be a great choice.

 

Fuh Shyan Co., Ltd. provides many series of ergonomic computer desk chair which can reduce the amount of stress put on your body from incorrect posture. A good ergonomic task chair also keeps you comfortable and focused on your work.

 

Their high quality D Series, T Series and H Series of ergonomic computer desk chairs, hope you can find the right one in your working life. Get more details about ergonomic office chairs, try to visit Fuh Shyan.

SL-T1 Ergonomic Office Task Chair

SL-T1 Model Ergonomic Office Task Chairs. This ergonomic task chair can adjust its armrest, seat depth (slide), seat height, backward strength, and backrest tilt (3 stage). It is with wire control mechanism or T-series mechanism.

Article Source: https://www.omnicoreagency.com/best-ergonomic-office-chairs/

How To Choose An Electric Strike Lock

The electric strike lock may not be a colorful component in a locking system, but it is one of the most important. This type of lock is not only cost-effective, but also a better alternative than electrified lock mechanisms in some circumstances.

 

Reasons for An Electric Strike Lock

Electric strikes are devices installed on doors to allow entry via an access system or remote release system.

 

Unlike a magnetic lock, a strike does not secure a door; that’s the responsibility of the door handle or lockset. The electric strike allows access to a secured door with a key card, pass, etc., without the need for a key to the lockset.

 

Types of Electric Strike Locks

There are two styles of electric strike lock:

 

  • Fail-Safe Locks

Fail-safe locks (also called fail-open) operate as a magnetic lock would. A direct electric current is applied to the strike, causing the door to lock. In a power failure, the door can be pushed or pulled open.

 

  • Fail-Secure Locks

Fail-secure locks (also called non-fail safe or fail-locked) open when an electric current is applied to them. In a power failure, this kind of lock will remain locked, although the mechanical can still be used to open the door from the inside.

 

An electric strike lock is useful on any door where high traffic occurs and requires monitoring or where items need to be secured and safeguarded. It also regulates employee access and helps prevent employee theft.

 

Choosing An Electric Strike Lock

Choosing the right kind of electric strike lock depends on the kind of door you have. The door material, and whether the door is internal or external, double or single, determines which electric strike lock is best. Strikes are available for nearly all door styles and of various material types, like aluminum and timber.

 

Security and Monitoring Requirements

The level of security desired will impact the type of strike that is best for your doors and circumstance.

 

For example, a low-security situation with no defined holding force may only require a low-cost electric strike. However, in a high-security environment, a strike with a maximum holding force of 1,500 pounds or more may be necessary.

 

Most electric strike manufacturers produce strikes with or without a monitoring facility. Door state monitoring should involve the use of a separate reed switch on the door or frame.

 

Type of Lockset

Your electric strike lock must be compatible with the type of lockset on your door. Use the lockset manufacturer’s compatibility chart to determine if your electric strike works with the lockset in question.

 

Latch Bolt Dimensions

Similar to a lockset, your choice of electric strike lock will need to accommodate the type of lock bolt sizes. Make sure that the centerline location of the latch bolt is correctly positioned around the centerline of the lockset to ensure that the lock will work as desired.

 

Power Needs

Most electric strike locks are 24 VDC, although 12 and 24 VAC options are also available. Choosing AC or DC power is critical because each strike application is different. Consider regulated or filtered power sources where practical as these sources will extend life to the strike’s operating capacity.

 

Code Compliance

Fail-secure electric strike locks must be used on fire-rated doors so that the door automatically goes into a locked position when the power is turned off. Because fail-safe locks go into an unlocked state when no power is applied, they do not meet code requirements for fire doors.

 

Consult the professional electric locks company if you are uncertain about what kind of electric strike lock you need for your building or office. Here, I recommend that you can visit Pongee Industries Co., Ltd.

 

Pongee is an experienced automatic identification systems manufacturer in Taiwan. They have different type of high quality electric strike locks to meet various needs of clients. If you need more information about strike locks, welcome to check out their product pages and feel free to send inquiry to Pongee.

 

 

Article Source: KENNYSLOCK.COM

Casters for Specific Applications: How and When To Choose Office Chair Caster Wheels

The good news is that you can find casters for office chairs, desks and even workstations to keep things rolling easily.

 

Your employees would love to use chairs and desks that are mobile for the right reasons. If you select the right caster, your office chairs can roll and move around easily and more importantly, quietly without the need of ugly plastic mats.

 

It is also seen that choosing the right office casters can improve workplace ergonomics. This means you can select the right casters and indirectly keep your staff healthy and happy.

 

How Can Technically Advance Office Chair Caster Wheels Positively Affect Your Workplace?

 

Modern office furniture caster wheels can roll and swivel even on carpeted floors. The innovative bearing and wheel design makes it easy for chairs, desks and other office equipment to move over carpeted areas or on floors with rugs with ease.

 

This easy movement makes work more comfortable for employees who have to sit in chairs for extended periods. What’s more interesting to note here is that ease of movement translates into increased productivity and efficiency. Not to forget, you can reduce workplace overexertion.

 

Yes, Office Casters Can Be Quiet!

 

Perhaps the last things you would want in your office are noisy wheels and unwanted squeaky sounds of rolling office chairs and equipment. You can now find ‘practically’ silent office chair casters that can maintain the mobility of your office furniture and equipment without adding to the noise. Remember, ‘silent’ office casters can help your employees stay focused on the task and help them become more productive.

 

No Need for Ugly Carpets

 

With innovative materials used in office chair casters, there will no longer be need for unattractive plastic mats or carpets in the office. “Non marking” casters do not mark or strain the tiles and at the same time, extend the life of your carpet or rug.

 

Because office casters can now be easily replaced, investing in high quality office casters make more financial sense than ever. After all, you no longer have to add the inconvenience of buying new office chairs to your budget.

 

How to Replace Your Office Chair Casters

 

Well, buying new chairs just because your office chair wheel breaks is history now. Chair casters can be easily replaced and replacement casters are affordable as well.

 

Before you proceed with the replacement, make sure:

 

  • The replacement caster wheels you choose match the stem and wheel of your existing caster.
  • Caster wheel you choose for replacement should show best performance on your office floor.

 

Remember that chair casters are differentiated by their diameter. Larger wheels can make your chair sit higher. On the other hand, caster with smaller wheels can lower your chair.

 

Hard wheel casters are designed for use on carpeted floors. Soft wheel casters can be used on hard floors (wooden and tile surfaces).

 

Where Can You Find Quality Caster Wheel Replacement?

 

About this question, I can recommend a manufacturer to you – that’s ENJOYING GO Co., Ltd.

 

ENJOY is a professional caster wheel manufacturer in Taiwan. They offer kinds of caster wheels for office chairs and home furniture. If you need more information about caster wheels, try to visit ENJOY and get more selections of PU caster series.

 

 

Article Source: http://casterwheelguide.com/selecting-caster-wheels/

6 Common Problems with Mesh Office Chairs

Ever since the Aeron chair burst onto the scene many years ago, mesh office chairs have been extremely popular. Mesh chairs are very unique; from their original styling, to the way the user feels when they sit. Because of their popularity, almost all office chair manufacturers now have their own version of a mesh chair. This means that the market is now flooded with mesh chairs ranging from cheap import chairs to very high end ergonomic chairs that are made to order in the USA. The mesh office chair topic is very polarizing as can be expected with any popular item. People seem to either love mesh chairs or hate them. In this article, we will share with you the downsides to mesh office chairs and the reasons why they are not a fit for every customer.

 

Before getting started it is important to understand that there are three distinct types of mesh office chairs. The first type is a mesh seat and back with no padding. Mesh is simply stretched across a chair frame on the seat and back. The second type is a mesh back with a padded mesh seat. This chair will have a seat that feels like a typical padded office chair but the backrest will have mesh stretched across the frame. The third type is a padded mesh seat with a padded mesh back. These models use the mesh upholstery for looks, which creates a feel very similar to traditional office chairs.

 

  1. Mesh Seats with No Padding Can Sag or Be Too Stiff

One of the biggest problems with a mesh chair is that it is very difficult to design a mesh seat that is both comfortable and supportive. A mesh office chair will almost always be too soft or too hard. Most higher-end mesh chairs will be upholstered with a soft mesh while lower-end chairs will typical have a hard mesh. A softer mesh will be more comfortable initially for the user. It will feel smoother and will expand further which can create a more comfortable sit. The mesh will sink down a bit more and give the user the feeling of floating; this is something that many mesh chair users rave about. But, mesh that is allowed to stretch and contract a substantial amount over and over will eventually sag; this can lead to the customer having to replace the seat or whole chair. The other major problem with soft mesh is that expands and contracts more than hard mesh so it will not properly disperse your weight over the entirety of the seat. Instead, the mesh will create an uneven flex point that causes the majority of the pressure to be placed on the tailbone. This can cause pain, numbing or discomfort after using the chair for an extended period of time.

 

A hard mesh will be much more consistent in its performance over time but the comfort level is very low to begin with compared to soft mesh. The flex point described above will not be nearly as pronounced but there will be no chance that the user experiences a feeling of floating. The seat will be much too hard not to notice the seat. A hard mesh seat will feel similar to sitting on a surface like wood than a typical office chair constructed of foam and fabric.

 

Suggestion: Some products with soft mesh seats, linked above, have become incredibly popular. We recommend only using these types of chairs for less than eight hours per day with multiple rest intervals throughout the day to get out of the chair and walk around; this will help to reduce the tension caused to the tailbone as described above. We do not recommend chairs that feature a hard mesh seat.  There are many alternatives out there that allow a user to pair a mesh back with a padded fabric, leather or vinyl seat; this will result in a more comfortable sit as well as a more cost effective option.

 

  1. Mesh Can Be Abrasive to Skin and Clothing

Mesh upholstery is much coarser than leather or fabric upholstery so there is a higher chance for the coarse material to cause abrasions to the skin or damage to clothing, such as dress pants. It is important to understand that there is a wide range in the quality of mesh used on office seating. Better quality mesh will be soft and smooth compared to lower quality mesh. This helps to reduce the likelihood of skin irritation or clothing damage. Mesh is upholstery made completely out of man-made materials, unlike leather. In some instances, the polypropylene, polyethylene, nylon, PVC or PTFE can cause skin irritation to the user.

 

Suggestion: Our first recommendation is that users with any type of allergy to polypropylene, polyethylene, nylon, PVC or PTFE should avoid mesh office chairs because of the discomfort it may cause to skin. We also recommend periodically checking your clothing for any wear being caused by the mesh. This is especially important on items such as dress pants, dress shirts or clothing made from soft materials like silk. Our final recommendation is to avoid having bulky or bulging items like a wallet or cell phone in your back pants pocket. Extra wear can often be found in areas where bulky objects are present.

 

  1. Mesh Is Difficult To Clean

Cleaning options with mesh are going to be more limited than other chair upholsteries. Non-padded mesh can easily be dusted with a vacuum; however, cleaning the chair with paper products like napkins, paper towels or toilet paper will be more of a nuisance than a help. The mesh upholstery will shred the paper products and add to the mess. Using a cloth towel and water can also be a bit risky because the friction caused by scrubbing with a towel combined with getting the mesh wet may make the mesh fray or split apart. Padded mesh will be even more difficult to clean. Along with the problems of using paper products or a cloth towel and water, padded mesh will also be very difficult to vacuum since many of the dust, dirt and food particles will be in-between the mesh and seat foam.

 

Suggestion: Prevention is going to be the best method to keep your mesh chair clean. Avoid things that will add to the potential of the chair becoming dirty, such as: eating at your desk or wearing dirty clothes/uniform in the chair. Try to keep the area around the chair as clean as possible to reduce dust and dirt that can become present on the mesh. If you do need to clean the mesh, first try a vacuum. Make sure to be very gentle and avoid pressing down on the mesh. Let the vacuum hover just over the mesh. If a towel and solution is necessary, then gently rub the dirtied spot with a soft cloth and soapy water and allow to air dry.

 

  1. Mesh Is Not Versatile

Mesh isn’t usually the preferred choice of designers because it limits their ability to customize a space to their taste. There are many different mesh chairs on the market but most of them have very similar looks with a very limited color selection. Mesh is mesh and there isn’t really a way to dress it up. Some manufacturers offer different color options but the ability to choose between different patterns in order to create a unique office design isn’t going to be as easy as it is with fabric chairs.

 

Mesh is not a good option for industrial, manufacturing and warehousing applications because the mesh will act as a net, trapping small materials that will be very difficult to remove. Things like metal shavings, sawdust and chunks of plastic can damage the mesh or cause injury when someone unknowingly uses a mesh chair with an object lodged into it. Workers in these environments often carry tools that can be sharp or strong enough to puncture or rip the mesh when the user sits down. This is another hazard for a mesh chair in an industrial environment.

 

Chairs with mesh seats are not ideal for call centers or 24/7 work areas, like dispatch rooms. Mesh seats are not built to withstand the constant wear and tear of a round-the-clock application and are also not comfortable for 8-12 hours shifts due to the challenges mentioned above.

 

Suggestion: We recommend that mesh chairs be limited to applications like offices, schools and conference rooms. Mesh chairs fit better in these areas because the user is often sitting in the chair for a couple hours at a time and the environment will not be destructive to the chair.

 

  1. Mesh Creates a Cooler Office Environment

The biggest selling point for mesh office chairs is always the breathability. Airflow and keeping you cool is touted as the biggest positive by almost every mesh chair manufacturer. This selling point is only a positive for limited applications and users. If you live in a place like Florida or Arizona and your office has the windows open, then the breathability of mesh seems like the only way to go. For someone living in a cooler climate like Minneapolis or in a work area that has the air conditioning on high, then the breathability of mesh seems like a moot point and can be a disadvantage. Unless your office environment is warmer than a typical office environment, which is usually around 68-74 degrees, then the “cooling effect” of mesh is no longer an overall positive.

 

The breathability and “keeping you cool” selling point is also rarely a positive for half of the people using a mesh chair, which are women. Studies have shown that women feel cooler on average compared to their male counterparts. [i] Women are more likely to be chilly when men are comfortable, and more likely to feel comfortable when men are warm. Mesh chairs only exacerbate this problem and will often cause women to be uncomfortable due to being too cold.

 

Suggestion: We do not recommend purchasing mesh chairs solely due to their ability to keep the user cool unless the environment is abnormally warm compared to a typical office. If you decide to use a mesh chair it’s important to keep in mind that you may require warmer clothing to stay comfortable.

 

  1. Frame Can Be Uncomfortable

Since most mesh chairs are designed with little to no padding, the frame can often become more pronounced to the user. On a padded office chair upholstered in leather or fabric, the user will not come into contact with the chair frame because the foam padding will spill over the frame making for an even sit over the whole seat. Mesh chairs will be constructed by stretching the mesh over the chair frame and since there isn’t padding, the user’s legs, butt, back or shoulders may come into direct contact with the chair frame which can be uncomfortable. Another problem that may occur is reduced blood flow to the lower legs due to the front of the chair seat frame cutting off circulation. Some chair models do a better job than others to help alleviate this problem. A waterfall seat shape is a design that has a seat front that drops off dramatically which helps to reduce poor circulation. Other chair models may place a small piece of foam on the chair front only, in an effort to help reduce this problem.

 

Suggestion: Look very closely at the chair frame with respect to the mesh around it. If there is a thick plastic frame that is visible outside of the mesh, then there is a strong chance that the problems described above will be present. Try avoiding these types of chairs. If you have already purchased a chair with these problems and are looking for relief, then try placing a folded piece of clothing or small piece of foam over the portion of plastic that is causing discomfort.

 

Final Thoughts

While there are many positive aspects to mesh office seating, the negative aspects can often be too overwhelming to justify going with a mesh office chair over a standard office chair. It is important to consider many factors in the work environment if mesh is going to be the ideal choice. Who is going to be sitting in the chair? What length of time will the chair are used per day and per sitting session? What is the average temperature in the work environment? Is the customer okay with limited colors and designs? For specific applications and users, mesh can work out great but it may not be the best fit for everyone.

 

Have any interest in mesh office chairs? Try to visit the website of VOXIM, the company of specializing in kinds of office chairs, to learn more information about ideal mesh chairs.

 

 

Article Source: https://www.btod.com/blog/2017/01/29/6-common-problems-with-mesh-office-chairs/

To Have Comfortable Working Environment, Choose Right Office Chairs First

Many people don’t realize the importance of a good office chair. That is, until you sit in a bad one for 40 hours a week. Chances are that it isn’t necessarily that you are sitting so long; but that your chair is not made to give you the most ergonomic seat and that can lead to a lot of fatigue.

 

You will want to take into consideration how tall you are how wide of a seat you want and what kinds of support features you like.

 

First look at the height of the chair. You should find one that has easily accessible controls for moving the seat up and down. Typically, your feet should touch the ground with your legs horizontal to the floor and your arms at the same height, or higher, than your desk. Good chairs also feature controls for seat tilt as well. This will help you get the right angle so you are in the correct position to support your back. Rounded seats will be much more comfortable on the backs of your legs as well. Back height adjustments are great if you will be sharing this chair with others in your home or office.

 

A good ergonomic office chair will offer you a lumbar support of some kind. This will keep your lower back arched the way it is supposed to, to avoid aching in that area.

 

Pay attention to the material that the chair is covered with. There should be extra padding on the seat, and/or backrest for ultimate comfort. Leather chairs are often softer and plusher, as well as being easy to clean. Mesh chairs breathe well and will keep your back from sweating.

 

The last thing to consider is mobility. Does it swivel? Does it weigh too much to easily move along the floor? Most chairs are made to be lightweight enough that you can roll without much effort.

 

Taiwan local company Fuh Shyan Co., Ltd. and VOXIM Co., Ltd. are professional and reliable office chairs manufacturer in the industry. They can offer you kinds of office chairs including executive desk chairs, lounge seating, public seating, mesh chairs, ergonomic computer desk chair etc. To have the most comfortable working environment, please choose right ergonomic office chairs first. Welcome to visit the website of Fuh Shyan and VOXIM to find out the most suitable office equipment.

 

 

Article Source: https://hubpages.com/living/Best-Top-Rated-Executive-Ergonomic-Mesh-and-Leather-Office-Chair-Review

What Is a Proximity Reader?

If you are in the process of updating your home’s or business’s security system or if you never had such a system and you are planning to invest in one, there are probably a lot of industry terms you don’t understand very well. That is why, in this article, we are going to talk about two important parts of any security access system, the proximity card and the proximity reader.

 

Proximity cards, also referred to as prox cards, are different than the magnetic stripe cards, because they do not need to be inserted into the reader device to grant access in the secured area. We say “grant access” because the majority of proximity cards and proximity readers are used as a part of home or business security system. Other uses include library cards, contactless payment systems or in public transit fare. Proximity cards are practical due to the fact that they can easily be read through a wallet or a purse.

 

There are two main types of proximity cards: passive and active. Passive prox cards have a limited range and are widely used to grant access in office buildings. Active cards, also called vicinity cards, have a greater range (150 meters), due to the fact that they use and internal lithium battery. They can be used to easily access courtyards from inside of a vehicle or from automated toll collection.

 

Now, in case you were wondering “What is a Proximity Reader?” they are devices that can store details about the identity of the cards holders, granting them access to otherwise restricted areas. This system is similar to the “chip and PIN” bank cards, with the difference that the proximity reader grants access using radio frequencies and does not need actual insertion of the card. Also, they offer more security to their holders, due to the fact that they are harder to copy. Another great advantage of these readers is the fact that they are quite sturdy and do not need any maintenance.

 

Another term you might encounter when browsing for this type of access system in “Contactless Smart Card”, which is basically the same thing, with the difference that they use advanced methods of data encryption and authentication, meaning that they offer a higher level of security. Besides this general information, there are various technologies that are used in the manufacture of proximity cards and readers.

 

If you are planning to invest in such a system, you must know that the prices are very different from one product to another. For example, the price for a single card ranges from $2 to $200, while for the proximity reader you can pay from $100 to $400.

 

Before making any purchase, we advise you to ask the advice of an experienced security technician, just to make sure that you choose the right system for your needs. The good news is that the majority of shops, even online ones, have an assistant which can help you make the right decision.

 

Pongee Industries Co., Ltd. is the manufacturer of proximity reader. If you are looking for the best proximity reader, don’t miss Pongee’s website, we can offer clients kinds of high quality products. Contact with Pongee to obtain further product information!

 

 

Article Source: http://EzineArticles.com/8665232

Public Seating Is Not Only For the Public but Also For Your Business

Public seating serves only one function, and that is to seat the public. It can be in open or closed spaces, indoors or outdoors. The public cannot be expected to think that having seating is a guaranteed right, but it does help if the seating is comfortable and made memorable by its construction and design.

 

Public seating can be used for many different purposes. It can be used to make a statement, and this is one of the areas where design firms can use public seating to their advantage. In open outdoor spaces, where there is little concern for matching or complimenting decors, a strategically placed custom- designed setting can be used as to drawn attention to design capability, products or services. While there are no legal requirements or legislation for seating in the public sector, there are some regulations that should be followed when seating is installed in commercial enterprises.

 

Since public seating is not a guaranteed right, there can be some open discussions concerning the use. If it is installed indoors as a courtesy to your visitors, you are free to do whatever you wish with it, but there are a few precautions. Your primary concern will be that of the quality. Over the life of your establishment, there may be thousands of people who will visit your premises, and your seating should be constructed to handle the heavy use.

 

In the U.S., seating that meets the Business and Institutional Furniture Manufacturer’s Association American National Standards Institute/ (ANSI/BIFMA), is certified as meeting performance requirements. Metals such as steel and aluminum usually last longer, and injected-molded foam cushions are likely to retain their shapes for longer periods. It may be better to avoid cloth or similar fabrics, because they are difficult to clean, and degrade quickly with frequent use.

 

There is no reason why your seating should not be comfortable. Although your concern may initially be that of durability, your visitors will be impressed and retain a more favorable impression with comfortable seating. You can offer as many accessories that you consider appropriate, such as matching end tables, and arm rests. Many of your visitors may also appreciate attached cup holders and a special touch can include power outlets for charging and operating mobile electronic gadgets such as cell phones and tablets.

 

The arrangement and layout of the seating governs the functioning. Some degree of flexibility may be desirable, as changes may be sometimes necessary. Your system should be easy to re-arrange in different configurations, and one of the most efficient ways to do this is to use a modular design that allows you to place or replace parts independently.

 

What is achieved with your public seating system will depend on your supplier. A solid trusting relationship forms the base for achieving satisfactory results. Many suppliers may have the expertise in design architecture, engineering and manufacturing of seating for public places, but they may lack the necessary skills that relate to developing relationships. As a result, you may not feel comfortable, working with ineffective communications or poor explanations.

 

You can help the perception of your business with public seating. There should be some careful planning when buying public seating for your business. You can try to visit the website of VOXIM Co., Ltd., the professional manufacturer of public seating.

 

Ergonomic design and comfort with vast range of options makes this the ergonomic public seating choice for any type of facility requirement. VOXIM offers various types of public seating to satisfy different needs!

 

 

Article Source: http://EzineArticles.com/8181128